Stainless Glycol XL Chillers – 4 Size Options 2/3HP – 3.33HP


2/3HP – 3 1/3HP

Current Lead Time: 3-4 weeks

4 Sizes to choose from
1 year warranty
Proudly Built in USA

Clear selection


Item Description

Our Stainless Glycol XL line is a series of 4 chillers made with 304 stainless steel that have a significantly larger reservoirs than our standard line, the XL line also offers chillers with higher cooling capacities.  The 2 piece lid allows you to route tubing and cords through the rear section and have access to the tub through the front portion of the lid.  The rear section has 16qty 7/8″ holes to accommodate 3/8″ or 1/2″ ID silicone tubing, plastic caps are provided to plug the holes not in use.  There are 2 additional holes to run pump power cords through.

These glycol chillers are suitable for applications down to about 5F depending on the heat load.  This makes it ideal for the brewing market, along with many other low temperature applications.  The built in controller maintains the temperature of the glycol at the set point.  It can be used as a typical laboratory bath chiller or by using a submersible pump, chilled glycol can be pumped out to equipment requiring cooling.

Depending on application (desired operating temp/freeze point) you can use any combination of water/glycol you prefer.  It’s typical for brewing applications to use about 33-50% glycol to water.  On our testing down to -14F we used a 50/50 mix without any freezing issues.  It’s our recommendation to use a 50/50 mix due to ease of calculating the mix and the buffer it provides compared to 33% mix which if off just a little bit can freeze at normal operating temperatures.

Intended for maintaining fermentation temps/crash cooling.  Not recommended for dropping wort from boiling temps.  It is common practice to either use a 2 stage system where the chiller pre-cools tap water that then cools the boiling wort, or tap water is used first to drop the temps down to about 100F, then switch over to using the chiller.  Glycol returning to the chiller should never be allowed to reach more than 100F.

It is typical to use one pump per fermenter or vessel you wish to cool.  In this type of setup each pump requires an individual controller to turn each pump on/off independently. The controller on the Glycol Chiller will regulate the temperature of the glycol (for example 28F), the controllers on the pumps would regulate the temperature of each vessel independently by regulating the flow of 28F glycol to that vessel.  Each chiller in the Glycol XL line has through lid holes for running either 3/8″ ID or 1/2″ ID silicone tubing, along with the power cords for the pumps.  The each chiller is setup to handle 8 pumps, you can drill additional holes if additional pumps are required.  Caps are supplied to seal off unused holes.


Chiller Specs




Reservoir size

Nominal Tank size (Actual fill volume)




2/3 HP


8 gal (6.9 gal)




1 1/3 HP


17 gal (14.7 gal)




2 HP


26 gal (21.9 gal)




3 1/3 HP


30 gal (25.2 gal)


(Nema 6-20P Plug)




Sizing a Glycol Chiller for Brewing:

These suggestions assume a decently insulated vessel (neoprene jacket or better) in a modest ambient temperature of 80F. If your setup is uninsulated, or running in hotter ambient conditions you’ll need to allow for more BTU/hr. The cold crash is figured for about 18hrs, if you want a faster crash you’ll need to add more BTU/hr. When in doubt, use the suggestions for a vessel 1-2 sizes bigger than your actual size.



Fermentation Temps


During Cold Crash


Maintain Cold Temps


7 gal

60 BTU/hr

300 BTU/hr

120 BTU/hr

14 gal

90 BTU/hr

600 BTU/hr

180 BTU/hr


150 BTU/hr

1000 BTU/hr

300 BTU/hr


300 BTU/hr

2000 BTU/hr

600 BTU/hr


450 BTU/hr

3000 BTU/hr

900 BTU/hr


600 BTU/hr

4300 BTU/hr

1125 BTU/hr


850 BTU/hr

6000 BTU/hr

1600 BTU/hr

10 BBL

1100 BTU/hr

8650 BTU/hr

1900 BTU/hr


Additional information

Technical Specs

• Up to 8 fermenters can be hooked up to the chiller
• Lowest recommended operation 5F (achieving these temperatures is highly dependent on application)
• 6\' power cord
• 1 year warranty
• Proudly Built in USA


2/3HP, 1 1/3HP, 2 HP, 3 1/3HP


Free Ground Shipping, Customer Pickup, Commercial Freight, Commercial Freight w/Liftgate, Residential Freight, Farm, Rural Commercial or Residential Freight w/Liftgate


There are no reviews yet.

Be the first to review “Stainless Glycol XL Chillers – 4 Size Options 2/3HP – 3.33HP”

Your email address will not be published. Required fields are marked *

You may also like…

Glycol Pumps
Glycol Pumps
FREE SHIPPING on Orders Over $99 (Continental 48 States)  
$49.99$129.99 Select options
Glycol Pump Controller
Glycol Pump Controller
FREE SHIPPING on Orders Over $99 (Continental 48 States) Controller for Glycol Pumps Plug & Play 1100W Max load Will control both a cooling device (glycol pump) and a heating device (heat pad/ immersion heater)  simultaneously to maintain fermenter set-point.
not rated $49.99 Add to cart
Sale! Glycol Chiller Accessory Package
Glycol Chiller Accessory Package
Glycol Pump Glycol Controller 15' to 45' Silicone Tubing 4 sets of Quick Disconnects Glycol (optional)
not rated $179.99$500.99 Select options
Propylene Glycol
Propylene Glycol
FREE SHIPPING on Orders Over $99 (Continental 48 States) 100% Propylene Glycol Food Grade
not rated $39.99$74.99 Select options
Silicone Tubing for Glycol Chillers
Silicone Tubing for Glycol Chillers
FREE SHIPPING on Orders Over $99 (Continental 48 States) 10' minimum order Sold by the Foot
not rated $1.99$3.79 Select options